top of page
To test this feature, visit your live site.
Forum
Welcome! Have a look around and join the discussions.
Welcome to our guides section, where you can find helpful information and tips on how to use our smart systems.
New Posts
- GrandstreamStep 1: Access the Grandstream PBX Web Interface 1. Log In: Open a web browser and enter the IP address of your Grandstream PBX system. Log in with your administrator credentials. Step 2: Configure the Blacklist 1. Navigate to Settings: • Go to PBX → Call Features → Blacklist. 2. Add a Number to the Blacklist: • Click on Add to create a new blacklist entry. • Blacklist Number: Enter the phone number you want to block. • Note: You can add a description or note for reference. • Click Save to add the number to the blacklist. Step 3: Create Inbound Rule to Use the Blacklist 1. Navigate to Inbound Routes: • Go to PBX → Call Control → Inbound Routes. 2. Create a New Inbound Route or Modify an Existing One: • Click on Add if you want to create a new route or click Edit next to an existing route. 3. Configure the Inbound Route: • Route Name: Give your route a name for identification. • DID Pattern: Set the DID pattern if applicable. • Caller ID Pattern: You can leave this blank unless you want to set specific caller ID patterns. • Blacklist: Set this to Yes to enable the blacklist feature for this route. • Default Destination: Choose where you want the call to be redirected (e.g., hang up, send to voicemail, etc.). 4. Save the Inbound Route: • Click Save to apply the changes. Step 4: Apply Changes 1. Apply Configuration Changes: • Click on Apply Changes at the top of the web interface to activate your new settings. Verification • Test the Configuration: • Call the PBX from the number you added to the blacklist to ensure it’s blocked as expected. Additional Tips • Updating the Blacklist: • If you need to block more numbers, simply repeat Step 2 to add more numbers to the blacklist. • Whitelist Important Numbers: • If you have a whitelist feature, make sure important numbers are added to avoid accidental blocking. By following these steps, you can successfully block unwanted phone numbers on your Grandstream PBX system. If you encounter any issues, consult the Grandstream user manual or contact their support for further assistance.
- Sonos1. Check HDMI ARC Connection: Ensure that your Samsung Frame TV is connected to a device (such as a soundbar or AV receiver) via HDMI ARC (Audio Return Channel). The HDMI ARC port on your TV should be labeled accordingly. 2. Access TV Settings: Using your Samsung Frame TV remote, press the Home or Menu button to access the TV's settings menu. 3. Navigate to Sound Settings: In the settings menu, look for the "Sound" or "Audio" option. This may be located under the "Settings" or "System" menu, depending on your TV model. 4. Select Audio Output: Within the Sound settings, there should be an option to select the audio output. Look for an option related to "Speaker" or "Output" settings. 5. Choose HDMI ARC: Navigate to the audio output options and select HDMI ARC as the preferred output. This option may be labeled as "HDMI-ARC," "External Speaker," or something similar. 6. Confirm and Save Settings: Once you've selected HDMI ARC as the output, confirm your selection and save the settings. Your Samsung Frame TV should now output audio through the HDMI ARC connection to your connected device. 7. Adjust Audio Settings (Optional): Depending on your preferences and the connected device (such as a soundbar or AV receiver), you may need to adjust additional audio settings, such as volume control, sound modes, or audio format settings.Like
- Windows OSIt’s possible to use the Microsoft Edge browser to access your Hikvision cameras or NVR/DVR. Then you can see the live view, playback mode, download footage and adjust other settings. This guide shows how to use the Microsoft Edge browser to view Hikvision cameras, NVR, and DVR. The trick is to enable the built-in Internet Explorer mode. As you may know, Internet Explorer has been serving the tech community for 25 years and Microsoft is finally ending its support. The end-of-support date will be June 15, 2022. After the Windows 10 update 21H2, the Internet Explorer browser will be hidden/removed from the OS. Once they do that, you need to use other browsers to access the CCTV systems. The instructions shown here are valid for Hikvision devices, logo, or OEM versions. Actually, the same settings are applicable to their surveillance manufacturer. If the Internet Explorer is gone, try to use this method to see the camera via the Edge browser. In this example, we use the instructions presented by LTS (which is a Hikvision OEM reseller). The basic requirements: • Run the latest Windows Update. The Edge browser version should be up to date. The minimal version is 91.0.86, anything older won’t work. • Make sure the Edge Browser is not restricted by the business or the organization. Otherwise, some functions will not be available. How to view security cameras via the Microsoft Edge browser Step 1. Set the Edge browser as the default one. Open the Edge Browser from the Windows 10 PC first, then go to the three dots icon (…) and select Settings from the menu. Go to the Default Browser section. Turn on Allow sites to be reloaded in Internet Explorer mode. This requires restarting the Edge Browser to take effect. Note: If you do not see this function, that either means this Edge browser is not supported by this function or the Internet Explorer browser has not been restricted from the Windows10 system yet. You should still be able to find Internet Explorer 11 from Windows Search. Step 2. After you restart the Edge browser and go to the NVR/DVR Login page, nothing will appear different on the screen. This is because you need to Reload in Internet Explorer Mode from the Menu. Go to the three dots (…) button, then Tools, and click on Reload in Internet Explorer mode. Step 3. After the browser reloads again, you’ve entered the Internet Explorer mode. The most noticeable difference is the prompt message at the top of the page. Note: Do not click Leave. Edge will revert back to regular Edge mode. If you accidentally click Leave, you need to go again through the steps and reload the Internet Explorer Mode from the Menu. Step 4. For the next step, type the IP address of the NVR/DVR or camera and enter your username/password. Then you should see the “please download plug-in” message on the center of the screen. This is the plugin that allows the camera to function normally via the web browser. Download the plug-in and install it. After fully loading, Refresh the page, and click Allow.Then, you should be able to see the video after clicking the Play All button. Basically, that’s all, everything should be exactly the same as Internet Explorer. You should be able to view the camera streams without any issue, playback, adjust settings, etc.
CHECK OUT OUR NEW ONLINE SHOP!
We offer a wide variety of quality smart electronic components & services to fit every client's project.
bottom of page